A circle looks perfectly round in your SVG editor. You send it to your pen plotter, but the result on paper looks slightly oval.
Perhaps the drawing is wider than expected, compressed vertically, or distorted near certain parts of the curve.
The obvious reaction might be to change the SVG until the plotted result looks right.
But a distorted circle does not automatically mean that the SVG is wrong.
The difference may come from X/Y scaling, mechanical alignment, backlash, pen movement, paper positioning or the way your plotting software imports the file.
Before correcting anything, it helps to identify which part of the workflow is responsible.
1. First, confirm that the SVG is actually circular
Start with the source file.
A circle in SVG may be defined using a <circle> element, a path describing a circular shape, or an ellipse with equal horizontal and vertical radii.
But even correct circular geometry can be distorted by transformations applied during editing or import.
Check whether:
- The drawing has been stretched non-uniformly.
- The document’s physical dimensions are correct.
- Any transformations preserve the intended proportions.
- The plotting software imports the file at its original scale.
- Automatic fitting or resizing has been disabled.
A circle that has already become elliptical inside the plotting software is a file-preparation problem, not necessarily a mechanical one.
Do not begin adjusting the machine until you know that the geometry being sent to it is correct.
2. Create a simple geometric test
A small test drawing can help distinguish dimensional errors from other problems.
Save the following code as circle-accuracy-test.svg:
<svg xmlns="http://www.w3.org/2000/svg"
width="120mm"
height="120mm"
viewBox="0 0 120 120">
<rect x="20" y="20"
width="80" height="80"
fill="none"
stroke="black"
stroke-width="0.2" />
<circle cx="60" cy="60"
r="40"
fill="none"
stroke="black"
stroke-width="0.2" />
</svg>
This file contains two simple geometric elements:
- An 80 × 80 mm square.
- A circle with an 80 mm diameter.
Both fit within a 120 × 120 mm SVG document.
The square provides straight horizontal and vertical references. The circle helps reveal distortion throughout a continuously changing direction.
Import the SVG without changing its physical dimensions.
Plot it using one pen on a securely positioned sheet of paper.
The 0.2 stroke width is only a display setting. The physical mark will depend on the pen and plotting workflow.
For the initial test, keep the machine’s normal settings unchanged.
3. Measure the result instead of judging it by eye
A circle that looks slightly oval may be difficult to evaluate visually.
Measurements provide more useful information.
Start with the square.
Check its horizontal and vertical dimensions, using the intended 80 mm measurements as references.
Then inspect the circle.
Measure its overall horizontal and vertical dimensions, taking care to account for the thickness of the plotted lines.
Ideally, measurements should refer to the intended path centreline rather than simply the outermost edges of the ink.
Record the results.
For example, imagine a test where:
| Measurement | Intended | Hypothetical result |
|---|---|---|
| Square width | 80 mm | 79 mm |
| Square height | 80 mm | 81 mm |
| Circle horizontal diameter | 80 mm | 79 mm |
| Circle vertical diameter | 80 mm | 81 mm |
These are illustrative values, not measurements from an actual plotter.
In this hypothetical example, both shapes show a similar dimensional difference between X and Y.
That would make inconsistent axis scaling worth investigating.
However, one test is not enough to identify the mechanical cause with certainty.
Repeat the drawing before making adjustments.
4. Recognise different kinds of distortion
Not all distorted circles indicate the same problem.
A. Consistent horizontal or vertical stretching
Suppose circles and squares are repeatedly wider or narrower along the same axis.
This pattern may indicate inconsistent scaling between the X and Y axes.
Possible explanations include incorrect software scaling, motion-system calibration or another systematic difference in axis movement.
Compare the measured dimensions with the intended geometry.
If the error is consistent across multiple tests, investigate the relevant scaling settings.
B. The square is not square
A different problem occurs when the square’s adjacent sides do not form right angles.
The dimensions may be approximately correct, but the geometry appears skewed.
This can suggest a perpendicularity or mechanical alignment problem.
Checking diagonal lengths can provide additional information.
For an ideal 80 × 80 mm square, each diagonal measures approximately 113.14 mm.
Unequal diagonals can indicate that the plotted shape is not square, although measurement uncertainty and other distortions must also be considered.
Do not assume that changing X/Y scale will correct an angular alignment error.
C. The curve is distorted near direction changes
Sometimes the circle is approximately the correct overall size but contains local irregularities.
A section may appear flattened, shifted or slightly deformed.
Possible contributors include mechanical play, pen-holder movement, motion-control behaviour or friction between the pen and paper.
Changes in movement direction can make certain mechanical effects more visible.
Repeat the test at a lower supported plotting speed, keeping the other conditions unchanged.
If the distortion changes significantly with speed, that observation may help narrow the investigation.
It does not, by itself, identify a single cause.
D. Repeated plots do not align
If the same drawing produces different positions on successive passes, the problem may involve repeatability rather than scale.
Possible causes include:
- Paper movement.
- Mechanical looseness.
- Inconsistent pen mounting.
- Positioning errors.
- Motion-system behaviour.
A repeatability problem should be investigated before applying a fixed geometric correction.
A calibration value cannot reliably compensate for an error that changes unpredictably between runs.
5. Separate paper, pen and machine problems
A useful diagnostic method is to change one variable at a time.
Start with paper stability.
Make sure the sheet is properly supported and does not move during plotting.
For practical mounting methods, see How to keep paper flat and secure during pen plotting.
Then check the pen holder.
A pen that moves or tilts inside its holder may affect the position of the physical tip.
This is particularly important when changing pens, but it can also influence a single-pen drawing.
The discussion How do you hold technical pens securely in a pen plotter? covers several relevant mechanical considerations.
Next, repeat the geometry.
Use the same pen, paper and settings to produce another test.
Check whether the same distortion occurs in the same way.
Finally, if your machine supports it, compare results at different plotting speeds.
Record the settings so that changes can be interpreted meaningfully.
The objective is to distinguish a consistent geometric error from a variable mechanical or material-related problem.
6. Use a dedicated alignment test
Once you have established that the problem is repeatable, a more comprehensive diagnostic drawing can help.
Plotterfolk provides a free Pen Plotter Alignment & Registration Tool.
The tool generates an SVG containing several geometric references, including:
- Horizontal and vertical measurement rulers.
- A square and its diagonals.
- Concentric circles.
- A continuous return path.
- Registration targets for multiple pens.
You can enter measured dimensions and review suggested X/Y scale corrections.
For example, if an intended 100 mm horizontal reference plots at 99 mm, the corresponding scale factor would be:
100 / 99 × 100 = 101.0101%
That result is a starting point for investigating a consistent dimensional scaling error.
It does not prove that scaling is the only problem.
The tool also supports measuring offsets between different pens and generating a verification SVG with inverse registration offsets applied to its test targets.
These functions are separate from correcting the machine’s mechanical geometry.
The tool does not modify firmware, calibrate motors or automatically repair the plotter.
Its results should be interpreted alongside the machine manufacturer’s calibration procedure.
7. Be careful with correction factors
It can be tempting to compensate for every visible distortion by stretching the SVG in the opposite direction.
This may improve one particular test drawing while hiding the underlying problem.
Before applying a correction, ask:
- Is the error consistent across repeated tests?
- Does it affect the whole plotting area or only one region?
- Is it present with different pens?
- Does the distortion change when plotting speed changes?
- Is the paper remaining stable?
- Is the source geometry being imported correctly?
If the error is consistent, a supported software or machine calibration adjustment may be appropriate.
If the error varies with location, direction or repeated passes, investigate the underlying mechanical or workflow conditions first.
Avoid adjusting belts, rollers, motor settings or other mechanical components without following the manufacturer’s instructions.
A poorly chosen adjustment may create additional errors.
8. Verify the correction with a second plot
After changing a setting, do not assume that the problem is solved.
Repeat the original test using the same SVG.
Measure the resulting square and circle again.
Compare the new measurements with the previous values.
If possible, also repeat the test in another part of the usable drawing area.
This can help distinguish an improvement across the machine’s working area from a correction that happens to work only in one location.
Keep a short record of:
- Original measurements.
- Settings changed.
- New measurements.
- Remaining distortion.
- Whether the improvement is repeatable.
A successful correction should produce a more accurate and consistent result, not simply a circle that looks better in one photograph.
A practical diagnostic sequence
When a plotted circle looks oval, use this order:
- Verify the SVG: Confirm that the source geometry and imported dimensions are correct.
- Secure the paper: Eliminate obvious movement or lifting.
- Check the pen: Confirm that the holder is stable.
- Plot simple geometry: Use a circle and square with known dimensions.
- Measure X and Y: Record actual horizontal and vertical distances.
- Repeat the test: Determine whether the error is consistent.
- Check geometry: Distinguish scaling, skew and local irregularities.
- Use an alignment tool: Investigate repeatable dimensional errors.
- Apply supported corrections: Change only what the evidence justifies.
- Verify again: Confirm the improvement with a new plot.
The key takeaway
An oval instead of a circle is a symptom, not a diagnosis.
A consistent difference between X and Y dimensions may indicate a scaling problem. Skewed geometry, local irregularities or inconsistent results can point toward other causes.
The most reliable approach is to start with known geometry, measure the physical result and change one variable at a time.
A small, repeatable test can provide much more useful information than repeatedly adjusting a complex drawing until it looks approximately right.
If you have encountered this problem, consider sharing the machine model, intended dimensions, measured results and the adjustments that made a difference.
Those details can help distinguish genuine calibration issues from paper, pen-holder and workflow problems.